EMS-16-R

• Extension of RC control with additional 8 or 12 switches
• Enables to control further 16 or 24 functions
• Decoding of switches with all BEIER-modules and the multiswitch decoder
• Connection requires free proportional channel
• Installation inside and outside the radio remote control box possible,
  extra box available
• Important: compatible with almost every radio control system,
  due to special data transmission

Description

The one channel multiswitch module EMS is an extension for RC-control, available with 8 and 12 switches in order to control 16 or 24 additional functions, such as triggering sounds and lights.

It is suitable for following BEIER-modules:

• Soundfahrtregler SFR-1, SFR-1-D und SFR-1-HL
• Soundmodule USM-RC-2, USM-RC-3 und USM-HL-2
• Fahrtregler UFR-1230 und UFR-1230-D

It is built into the radio control housing and requires for installation only one free proportional channel. For connection no additional decoder is required.

Due to a special data transmission the EMS is compatible with most 2.4 GHz systems. This transmission is carried out with time division multiplex, which leads to a response time delay of up to 1,4 s.

Each switch has three positions: up - middle - down. With the positions "up" and "down" at least two functions can be controlled. The switches have a pushbutton function, they returning automatically to neutral (middle position). With the memory setting from the sound modules SFR-1, USM-RC-2 and the multiswitch decoder MSD-16 each switching output can be activated/deactivated permanently.

The EMS is available in three different versions.

More information can be found in the operating manual (English).

Technical Data

Overview of compatible and not compatible radio remote controls

Sender	External housing necessary	EMS-Type	Compatibility
Graupner 4014	no	EMS-16-G EMS-24-G
Graupner mc-19	no	EMS-16-G EMS-24-G
Graupner mc-22	no	EMS-16-G EMS-24-G
Graupner mc-24	no	EMS-16-G EMS-24-G
Graupner mc-32	no	EMS-16-G EMS-24-G
Graupner mx-10, mx-12, mx-16, mx-20, mx-32	yes	EMS-16-G EMS-24-G	1)
Graupner mz-10, mz-12, mz-18, mz-24	-	-	3)
Robbe F-14	no	EMS-16-R
Robbe FC-16	no	EMS-16-R
Robbe FC-18	no	EMS-16-R
Robbe FX-30	yes	EMS-16-R
Spektrum DX5	yes	EMS-16-G EMS-24-G	2)
Spektrum DX6	yes	EMS-16-G EMS-24-G	2)
Spektrum DX7	yes	EMS-16-G EMS-24-G	2)
FLY SKY FS-T6	yes	EMS-16-G EMS-24-G
Turnigy 9X	yes	EMS-16-G EMS-24-G
FrSky Taranis QX7	yes	EMS-16-G EMS-24-G
JETI DC-16	yes	EMS-16-G EMS-24-G

Legend:
 

	Compatible (tested)
?	Should be compatible (not tested)
	Not compatible
1)	At transmitters of the MX-series, there is a feature that should be noted: The EMS module may only be switched on after the transmitter has bootet completly after power on! It still needs a switch installed in the plus line (orange cable) of the EMS, with the EMS can be turned on and off.
2)	At these radio controls, the switch inputs are not true proportional inputs, but only switching inputs. Therefore, you have to use a channel of a stick for connection of the EMS! This channel can no longer be controlled with the stick.
3)	Unfortunately, the transmitter encoder voltage of 0,7 V is not enough to operate the EMS processor (at least 2,5 V required).

Switch panel optionally available